2004-2005
Turn the ignition to run (one position before starting engine).
Ensure ODO/TRIP display screen is in the odometer mode. Turn ignition off.
While pressing ODO/TRIP button, turn ignition to run (one position before starting engine).
Continue to hold button for over 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2007
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
Vehicles with smart key system:
3.While pressing the trip meter reset button, press the “ENGINE START STOP” switch to IGNITION ON mode. Continue to press and hold the button until the trip meter displays “000000”.
Vehicles without smart key system:
3.While pressing the trip meter reset button, turn the ignition to run (one position before starting engine). Continue to press and hold the button until the trip meter displays “000000”.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
Turn the ignition to run (one position before starting engine).
Use the fuel button on the Driver Information Center to reach the ENGINE OIL LIFE screen.
Press and hold the select button on the DIC for 5 seconds while ENGINE OIL LIFE is displayed.
OIL LIFE RESET will appear on the DIC display for 10 seconds to let you know the system is reset. If the change oil light comes back on when you start your vehicle, the engine oil life system has not reset, repeat the procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1994-2009
Turn the ignition to run (one position before starting engine).
You can clear the message by pressing CLEAR once. Reset by pressing CLEAR for at least 8 seconds, until SERVICE appears on the display.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*The message can only be deleted when it is shown on the SID (Service Indicator Display).
1994-2002
Turn the ignition to run (one position before starting engine).
This message can be deleted by first briefly pressing the CLR button, then depressing it a second time for at least 8 seconds until “SERVICE” appears on the display and a chime sounds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*The message can only be deleted when it is shown on the SID (Service Indicator Display).
2003-2006
Turn the ignition to run (one position before starting engine).
Press the CUSTOMIZE button.
Select System Settings using the INFO dial. Press the INFO dial.
Select Service Info. Press in the INFO dial.
Select Reset Service Ind. Press in the INFO dial.
When asked Are you sure? Select Yes. Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Select Settings using the steering wheel controls (up or down arrow).
Press and hold the SET button until given audible confirmation.
Select Time for Service.
Press the SET button.
To the question Reset Service Ind? Select YES. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.