Hot to reset service light on a Seat Arosa
The SEAT owners manual for the Arosa states.
With the ignition switched off, press and hold the trip meter reset button below the speedometer.
Then, switch the ignition on and hold the reset button for atleast 10 sconds.
Dashes will then appear in the display.
The service has been reset.
Service indicator system Seat Cordoba, 1993, 1994, 1995, 1996, 1997, 1998, 1999
IN00, No service is required, standard display.
OEL, When 7500 miles has been reached before the yearly service is required.
IN01, Indicates time for the yearly service inc oil change.
IN02, Indicates it is time for the Major service. T
O RESET THE INDIVIDUAL COUNTERS.
1) turn on ignition (do not start).
2) Press the trip reset button button on the speedo (the trip value will not reset to zero but will reappear when the procedure is finished).
3) Turn off the ignition and thne release the trip reset button. In the LCD display you will see the word OEL. Using the minute set button for the clock (lower one) you will reset the OEL interval counter. Press it, hold, release, 5 horizontal lines will appear in the display.
4) press and release the trip reset button. In the LCD display you will see IN01 repeat step 3 to reset the inspection counter when required.
5) Again press the trip reset and rest the IN02 counter if necessary. If doing an oil change only reset the OEL counter. If doing an inspection service reset both the OEL and IN01 counters. If doing a full service reset all 3, OEL, IN01 and ,IN02.
6) Turn on ignition (do not start the car).
7) After the appearance of the IN00 display turn off the ignition.
8) You are done the trip counter should read as it did before you started.
PROGRAMMING THE INTERVALS TO REQUIREMENTS
With todays higher spec oils and/or peoples need and desire to service more regular there is a way to alter the counters to your prefered settings (within reason).
1) Turn on ignition (dont start the car).
2) press the trip reset button also press the Minute set button on the clock (lower one).
3) The LCD display OEL 1,S where the S indicates SET.
4) Using the trip reset button you can call up the following counter data in sequence.
OEL 1,S Distance counter for oil change (7500 standard).
OEL 2,S Time counter for oil change (12 months).
IN 01,S Time counter for yearly service interval (12 months).
IN 02,S Distance counter for full service (15000 miles).
5) Using the minute SET button on the clock (lower one) you can display the current value repeated pressing of the button will select a subsequent lower value and at the lowest level will reset to the highest and start to decrease again (so dont panic). the steps work in miles (500 at a time) and time steps in bi-monthly (1, 2months) i.e.1,2,3,4,5,6.
6) Once you have set the counter to the value you require turn off the ignition.
7) Job done
Reset maintenance light on Dodge Sprinter
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51″
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
Oil service reset Dodge Avenger, 2008, 2009, 2010.
Turn the ignition to run (one position before starting engine).
Fully depress the accelerator pedal slowly three times within 10 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Oil service reset Dodge Caliber, 2008, 2009, 2010.
Turn the ignition to run (one position before starting engine).
Fully depress the accelerator pedal slowly three times within 10 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Recent Comments