2007-2010
The “—” display can be reset while the ignition switch is “OFF”. When the display is reset, the time until the next periodic inspection is displayed and “PERIODIC INSPECTION” is no longer displayed when the ignition is switched from “OFF” to “ON”.
Lightly press the multi-information meter switch until the information screen switches to service reminder display screen.
Press and hold the multi-information meter switch for about 2 seconds or more to display the (wrench icon) and make it flash.
Lightly press the multi-information meter switch while the icon is flashing to change the display from “—” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.
Start the engine to verify the indicator has been reset.
2002-2006
*Diagnostic Reset Tool Required (please refer to TOOLS page)
2007-2010
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
Press and hold the on-board computer button on the direction indicator/main-beam switch until “RESET” appears in the lower display.
Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
Turn the ignition off and start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to run (one position before starting engine) and bring up the odometer reading. Turn the ignition off.
While holding down the “RESET” button turn the ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down the ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run (push START/STOP button once). Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the ěODO/TRIPî button, set the engine switch to run (push START/STOP button once).
Continue holding the “ODO/TRIP button for about 5 seconds. The resetting procedure is complete when “000000” in the trip metre flashes once and the message in the multi information display disappears.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates
3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine) for longer than 7 seconds. While doing this operation, the “engine oil replacement” reminder light goes off. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on by holding the START/STOP switch. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Recent Comments